TroubleShooting power supply
The Power Supply convert's your regular householdcurrent into low DC voltage used by the computer.When this component fails,there is simply no activitygoing on wih your computer.Remember to do theeasy troubleshooting first.Inspect the Power Supplyfor any damage.Double-Check all connections.
Learning how to check your power supply and how toreplace it when needed can be a life saver if you're acomputer buff or in business with the trusted PC.Don'ttake for granted the sinple pleasure of turning on yourPC and everything works just fine.
We turned on one of our computer's recently and if about one hour,it just re-booted itself.And it continued doing so about 10 times a day until we found out the power supply was the culprit.Things to look for when your power supplyis going bad or just dies on you are the following....
NO POWER TO THE COMPUTER
Here you must first check the wall outlet for powerby connecting another device such as a radio orlamp to be sure power is present.If the computeris connected through a surge protector,check itas well.
If the wall out has power,check the power cablegoing to the PC to see if AC voltage is makingits way to the system unit.Do this with the use ofa multimeter.If there is power,you will have to openthe computer and check for power from the powersupply to the motherboard.When using a multimeterto check voltage,be sure you have a good groundfor the black lead of the multimeter.
RE-BOOTING PROBLEMS
One main problem you may face with an ailing PowerSupply is that it may re-boot the computer without anywarning.All information is lost and it seems as though this happens at the worst possible time.Booting errorswhen the computer first start's up is another indicatorof this component going on the blink.
POWER DISTRIBUTION PROBLEMS
When the power supply begins to fail,you may receivepower at one device and not another.For example,theHard Drive may receive power but the CDROM Drivehas nothing at all.
Another headache with would cause re-booting is theintermittent power going to the drives or the motherboarditself.Follow the steps below to check your power supplyshould you experience some of the above problems.
CHECKING THE POWER SUPPLY
If the wall outlet,and the power cord are good,as well as the connection at the motherboard is secure.Thenyou may have to face the fact that the power supply itself is bad.If you have a Multimeter you can test the power supply output before purchasing a new one.Simply follow these steps.
Turn off the PC,but do not unplug it,open the system unit.Set the multimeter to read DC volts in the next range higherthan 12 volts.Locate a power connector similair to the harddrive,or floppy drive connector that is unused and turn onthe PC.You can also unplug a drive connector and use it as well.Turn on the PC and insert the BLACK probe into the power connector on one of the BLACK wires.Touch the RED probe to the YELLOW wire onthe power connector.
The multimeter reading should be +12 volts.Now touch the RED probe to the RED wire and the reading should be +5 volts.If no readings or different readings occured,you,ll have to replace the power supply.If the readings were correct,you should check the P8 or P9 connectors at the motherboard.These connectors may also be named P4 and P5.To check these connectors,perform the following...
Insert the BLACK probe into P8 at one of the BLACK wires.Insert the RED probe into the P8 connector at the RED wire.The readingon the multimeter should be +5 volts Check the power going to the Motherboard connections by inserting the RED probe into P8 at the YELLOW wire and you should get +12 volts.Leave the BLACK wire touching the black wire at the P8 connector.Check the BLUE wire and the reading should be a -12 volts.
Now move the BLACK probe to the BLACK wire on the P9 connector.Test the WHITE wire by inserting the RED probe and the reading should be -5 volts.Check the RED wires on the P9 connector and you should get +5 volts on each red wire.You won,t get exactly 5 or 12 volts but the readings will be very close,such as 5.02 volts.
If the Power Supply is a couple of volts off,in either direction,such as when the RED wire should be reading -5 volts but it reads -8 volts,or if there are no readings,replace the power supply.
DO NOT remove the power supply from the system unit casewhen performing these tests.DO NOT perform these tests if you do not feel comfortable.Be sure to remove any and all electrical static build-up from your clothes and body BEFORE touching any parts inside the system unit.And NEVER open the power supply case for any reason,since high voltage may be present.